point were high, and, next, C material, B material, E material, and F material were low values. The yield ratio became a high result in order of H material >A material >C material >E material >B material >F material. Table 4 shows the Charpy impact test result. The specimen name shows the kind and the position where it gathers the steel material. S shows the parent metal, f shows fillet, and h shows HAZ. beam upY.P. lowY.P. ε st T.S. ε u Y.R. EL. (N/mm2) (N/mm2) (%) (N/mm2) (%) (%) (%) A 409 391 1.29 555 15.2 74 28 B 332 332 0.55 528 16.1 63 31 C 386 364 1.27 548 15.6 71 29 E 330 322 0.80 514 16.1 64 33 F 318 311 0.45 511 15.0 62 29 H 400 374 1.44 536 16.4 75 31 A(web) 441 414 2.01 552 16.0 80 30 B(web) 394 372 1.20 535 15.5 74 29 C(web) 442 416 2.31 550 15.9 80 30 E(web) 397 375 1.31 558 16.0 71 28 F(web) 399 382 1.39 555 15.6 72 27 H(web) 449 408 2.29 542 16.4 83 32 upY.P:Yield point LowY.P:Yield point in the under ε st:Strain when strain stiffens T.S:Tensile strength ε u:T.S . Strain at time Y.R:Yield ratio EL.:Elongation specimen vEo(J) vBo(%)Tre(℃)Trs(℃) A s 19 88 22 24 B s 34 88 33 34 C s 286 1 -51 -48 E s 240 15 -39 -27 F s 283 6 -28 -23 H s 55 78 23 16 A h 199 7 -31 -28 B h 160 47 -7 -1 C h 250 2 -33 -33 E h 200 33 -23 -13 F h 260 10 -30 -27 H h 130 47 3 -2 A f 24 85 - - C f 282 0 - - H f 68 77 - - RH Depo 80 60 3 8 BH Depo 28 88 51 42 parent s(s) HAZ(h) fillet(f) Weld Metal Table. 4 Charpy impact test result Table.3 Tension test result 3. Experiment result 3.1 destruction properties All specimens except Cn0 destroyed the brittleness from the edge of the width of the flange in the beam flange welding toe of weld part. Cn0 destroys the brittleness from the welding first layer neighborhood. The destruction is the following two types. ① In the direction of the width of the flange when the position becomes a starting point within 10mm. There are a lot of cases of 0℃. ② When the position at 10mm or more becomes a starting point in the direction of the width of the flange. There are a lot of cases of room temperature. The P-δ curve of Fn1 and Hn1 decreases gradually when the load when maximum displacing increases the cycle, and the load has decreased obviously at the cycle to breaking. 3.2 skeleton curve and deformation capacity's indices It requested from the P-δ curve, and it shows the method of calculating the skeleton curve and the accumulation plastic deformation irreversible deformation in Figure 3. The skeleton curve accumulated and obtained the P-δ curve for the load to have exceeded the maximum value of the pre-loop in the P-δ curve. Table 5 shows the experiment result list. Accumulation value (ΣW) of the energy requested from energy (Ws) requested from the skeleton curve shown in Figure 5 when it compares deformation capacities of junction and each loop of the P-δ curve is thought. The actual experiment requested by expression 1 and 2, and examines the result by ηs and ηw. It examines ηsF and ηwF obtained by expression 3 and 4. 3
RkJQdWJsaXNoZXIy MjM0NDE=