alloy types AlMg3, AlMg5, AlMg4.5Mn and their welded joints by GMA and pulsed GMA welding were tested, too [7]. Mechanical properties of base materials (bm) and weld metals (wm) are shown in Table 1. TABLE 1 MECHANICAL PROPERTIES OF THE TESTED METALLIC MATERIALS AND WELD METALS Material Ry N/mm2 Rm N/mm2 A5 % Z % KV(200C) J KV(00C) J KV(-200C) J 37C bm 270 405 33.5 63.5 – >27 – 10 Cr Mo 9 10 bm 374 510 ≥20 – ≥34 – – KL7D bm 390 535 ≥19.0 – – – ≥40 E420C bm 450 595 30.7 – – >40 - X80TM bm(1) 540 625 25.1 73.1 – – ≥243 DO 76 bm 582 954 7.6 – ≥7 – – QStE690TM bm(2) 780 850 18.3 – 130 90 95 VIH-2 wm 410-485 535-58522.0-24.840.9-63.9 46-80 29-61 ESAB OK Flux 10.62/ OK Autrod 13.20 wm 450 590 – – ≥100 – – EB 12 wm 420-510 510-630 ≥22.0 – – – – Union K56 wm ≥500 560-720 ≥22.0 – – – ≥47 Böhler X90-IG wm(3) ≥890 ≥940 ≥16.0 – – ≥100 ≥90 AlMg3 bm 112 224 21.4 – – – – AlMg5 bm 185 288 14.5 – – – – AlMg4.5Mn bm 230 296 18.0 – – – – (1) KV (-60°C) = 128-208 J. (2) KV (-40°C) = 35 J, KV (-60°C) = 20 J. (3) KV (-40°C) = 80 J, KV (-60°C) = 60 J. The investigated non-metallic materials were as follows: silicon nitride ceramics (Si3N4, Re2O3, SiO2 and additive component Y2O3 or Yb2O3 or Dy2O3)[8, 9]; polymethyl methacrylate (PMMA) [10]; unidirectional carbon fiber reinforced plastic (CFRP), carbon fiber/epoxy, T300/914 [11, 12]; injection-molded composite, glass fiber/nylon 6, 6 [10, 13]. Compact tension (CT) and three point bending (TPB) specimens were tested for base materials and welded joints, while for testing of weld metal TPB type specimens were used. CT type specimens were cut from the sheets parallel and perpendicular to the rolling direction, so the directions of fatigue crack propagation were the same. For testing of weld metals cracks which propagate parallel or perpendicular to the axis of the joint were also distinguished. Compact tension shear (CTS) specimens were used for tests under mixed mode I+II loading condition. The specimens were cut parallel to the rolling direction, so the cracks were propagated perpendicular to the rolling direction. Tests were carried out according to the ASTM prescription by an universal electrohidraulic MTS testing machine. Experiments were performed by ∆Kdecreasing and constant load amplitude methods, at room temperature, in air, following sinus-type loading wave form. Stress ratio was constant (R=0.1), crack propagation was registered by compliance and/or optical method. DETERMINATION OF FATIGUE DESIGN LIMIT CURVES Values of threshold stress intensity factor range (∆Kth) and two parameters of Paris-Erdogan law (C and n) were measured according to prescriptions [14], values of fatigue fracture toughness (∆Kfc) were calculated from crack length measured on the fracture surface of the specimens by the means of stereo-microscope. Fatigue crack growth was determined by secant or seven point incremental polynomial method.
RkJQdWJsaXNoZXIy MjM0NDE=