33 / y σ σ 1 2 3 4 5 6 7 8 10 9 10 1 -1.29 2 -1.14 3 -0.98 4 -0.83 5 -0.68 6 -0.52 7 -0.37 8 -0.21 9 -0.06 10 0.09 11 0.24 12 0.40 9 10 11 12 8 9 12 10 9 11 3 1 2 (b) 0 200 400 600 800 1000 1200 103 104 105 106 107 108 109 Maximum Stress, (MPa) σmax Cycles to Failure, Nf Air, RT Ti-6Al-4V, Bi-modal Smooth-Samples FOD-Samples 3.2mm 1mm R= 0.1 0.5 0.1 300m/s 200m/s FODcracks Res. Stresses 20-50 mµ R=0.5 R=0.7 R=0.1 5 mµ Tensile 2 =5 m ci µ 30 mµ 10 mµ Fig. 4 S-N data show reduced fatigue life due to simulated FOD as compared to smoothbar specimens. 2ci is the surface crack length of FOD-induced microcracks. For failures at 107 - 108 cycles, the effect of local tensile residual stress (~300 MPa) in increasing the local maximum stress (and hence the local load ratio) has been illustrated by arrows and open symbols. Fig. 5 Lower stress fatigue loading after 300 m/s impact using 1 mm or 3.2 mm diameter steel shot caused crack initiation away from the indent site (marked by arrows): (a) 1 mm steel shot, nominally applied σmax = 325 MPa, R = 0.1, NF = 1.3 x 10 8 cycles, (b) 3.2 mm steel shot, nominally applied σmax = 325 MPa, R = 0.1, NF = 1.6 x 10 7 cycles, and (c) nominally applied σ max = 300 MPa, R = 0.1, NF = 1.3 x 10 7 cycles. 100 200 300 400 500 600 700 800 900 1000 1 10 100 1000 10000 Ti-6Al-4V, Bi-modal, Air, RT ∆σ= Y (2 ) √π c ∆KTH Surface Crack Length, 2 ( m) c µ ∆σ= Y (2 2 ) √π c + c0 ∆KTH (El Haddad) ∆KTH = 1.9 (MPa·m ) 1/2 (Worst-Case Threshold) Far-Field Stress Range, (MPa) ∆σ R=0.1 R=0.5 R=0.7 104 105 106 107 108 Fatigue Life (Cycles) Smooth- 200m/s LSP 300m/s LSP bar +200m/s +300m/s Ti-6Al-4V, Bi-modal R=0.1, =500MPa σmax base base rim rim/ base Fig. 6 Modified Kitagawa-Takahashi diagram representing the threshold crack-growth conditions (da/dN = 10-11-10-10 m/cycle) at R = 0.1 and 0.5 for FOD-induced small-cracks in bimodal Ti-6Al-4V. Plotted is the threshold stress range as a function of surface crack length. Data points are corrected for the stress concentration of the FOD indents. Fig. 7 Histogram showing the effect of laser shock peening (LSP) prior to the FOD event. FOD was simulated using 3.2 mm steel shot at velocities of 200 and 300 m/s. The sites of crack initiation, at base or rim at impact crater, are indicated.
RkJQdWJsaXNoZXIy MjM0NDE=