ICF10B

A brittle failure is assumed to initiate at a point if the maximum principal tensile stress there exceeds 2:34 0 . The ductile failure in the form of an adiabatic shear band ensues at a point as soon as the effective stress there has dropped to 90% of its maximum value at that point and the material point is deforming plastically. The computation of the numerical solution is continued till an element has been very severely distorted. Once a shear band has initiated, the time step size continues to decrease rapidly. The subroutine LSODE adjusts the time step adaptively in order to compute the solution within the prescribed accuracy. We note that no failure criterion has been implemented in the code. Neither the failed elements are eliminated from the mesh nor values of their elastic moduli are reduced. However, elastic moduli decrease because of the increase in the porosity, and the radius of the yield surface decreases because of the rise in the temperature and the porosity. For the four shapes of the notch tip considered herein, Fig. 2 depicts the dependence of the times of initiation of the brittle and the ductile failures upon the impact speed. For the blunt notch tip with a=b = 0:4 , where a and b equal the semimajor and the semiminor axes of the elliptical notch tip, the two failure modes occur essentially simultaneously; b = 0:15mm. The failure mode transitions from brittle to ductile at an impact speed of about 19m=s for the circular notch tip, and the ductile failure mode precedes the brittle failure mode for elliptical notch tips with a=b =2 and 10 . It provides an explanation for the different failure modes observed by Kalthoff (2000) and Zhou et al. (1996) in their experiments on very similar steels. Since the notches were cut by different techniques, the notch shapes may not have been the same in the two experiments. However, when a circular hole of radius r0 = 0:15 mm was located ahead of the circular notch tip of radius r0 with the distance, d, between the centers of the circular notch tip and the hole equal to 3r0; 4r0; 5r0 and 6r0 , the brittle failure always preceded the ductile failure. Whereas the brittle failure initiated from the point, P , on the lower surface of the circular hole that is closer to the notch tip, the ductile failure originated from a point either on the lower surface of the notch tip or on the upper surface of the hole. For the distance of 3r0 between the centers of the hole and the notch tip, the line joining point P to the center of the hole made an angle of 9 counterclockwise with the axis of the notch, this angle equaled 18 for the other three cases. Figure 3 illustrates the dependence of the times of initiation of the brittle and the ductile failures upon the impact speed for the four locations of the circular hole. 4 CONCLUSIONS For the impact loaded prenotched plate with the blunt and the circular notch tips considered herein, the failure mode transitions from the brittle to the ductile with an increase in the impact speed. However, when a circular hole of radius equal to the radius of the circular notch tip is located ahead of the notch, the brittle failure always occurs first and it initiates from a point on the lower surface of the circular hole. Acknowledgment: This work was partially supported by the ONR grant N00014-98-0300 to Virginia Polytechnic Institute and State University with Dr. Y. D. S. Rajapakse as the cognizant program manager. REFERENCES Batra, R. C. and Nechitailo, N. V. (1997). Analysis of failure modes in impulsively loaded prenotched plates. International Journal of Plasticity 13, 291-308. Batra, R. C. and Gummalla, R. R. (2000). Effect of material and geometric parameters on deformations near the notch tip of a dynamically loaded prenotched plate. International Journal of Fracture 101, 99-140. Batra R. C. and Ravisankar, M. V. S. (2000). Three-dimensional numerical simulation of the Kalthoff experiment, International Journal of Fracture, 105, 161-186. Batra, R. C. and Jaber, N. A. (2001). Failure mode transition speeds in an impact loaded prenotched plate with four thermoviscoplastic relations. International Journal of Fracture (to appear). Bodner, S. R. and Partom, Y. (1975). Constitutive equations for elastic-viscoplastic strain-hardening materials. Journal of Applied Mechanics 56, 527Gurson, A. L. (1977). Continuum theory of ductile rupture by void nucleation and growth. Part 1 Yield criteria and flow rules for porous ductile media. Journal of Engineering Materials and Technology 99, 2-15.

RkJQdWJsaXNoZXIy MjM0NDE=