notches, and its speed equals v0 . The plate is assumed to be made of a homogeneous and isotropic microporous thermoviscoplastic material, and it rests on a flat rigid smooth surface prior to being impacted. Batra and Ravisankar (2000) analyzed three-dimensional deformations of the plate and the projectile and found that the deformations of the central 75% of the thickness of the material closely resembled those obtained by the twodimensional plane strain analysis. Here we do not study deformations of the projectile, replace its action on the plate by prescribing the normal component of velocity of the plate particles on the impacted surface, and presume that a plane strain state of deformation prevails in the plate. All of the contact surfaces are taken to be smooth, and the bounding surfaces including those of the notches thermally insulated. However, heat conduction is considered in the plate. Noting that the bottom edge of the plate is far away from the notch, we assume that deformations of the prenotched plate are symmetrical about the horizontal centroidal axis, and examine deformations of only the upper half of the plate. Thus at a point on the plane of symmetry, the vertical component of displacement, the tangential traction and the normal component of the heat flux are set equal to zero. The thermomechanical deformations of the plate are governed by the balance of mass, linear momentum, moment of momentum and internal energy. The hypoelastic material of the plate is modeled by a linear relation between the Jaumann derivative of the Cauchy stress tensor and the elastic part of the strain-rate tensor D with Young’s and the bulk moduli decreasing affinely with an increase in the porosity. The material obeys Gurson’s (1977) yield criterion as modified by Tvergaard and Needleman (1984), the associated flow rule, Fourier’s law of heat conduction with the thermal conductivity decreasing affinely as the porosity increases, and the Bodner-Partom (1975) thermoviscoplastic relation _" p =D0 exp 1 2 K 2 3 2 e n ; K=K1 (K1 K0)exp( mWp); n= ^a + ^b; Wp = Z t 0 tr( Dp )dt; " p =Z t 0 2 3 tr(Dp Dp ) 1=2 dt: (1) Parameters D0; n; K1; K0; m; ^a and ^b characterize the material of the plate, is the absolute temperature, and Dp is the plastic part of the strain rate tensor. The material parameters were assigned the following values: Mass density = 7860 kg=m 3, specific heat = 473 J=kg C , thermal conductivity = 49:73W=m 2 C, Young’s modulus = 208 GPa , Poisson’s ratio = 0:3 , coeff. of thermal expansion = 11:5 10 6 = C, ^a = 1200 K , ^b = 0 , K1 = 2950MPa , K0 = 2937MPa , m = 3510MPa , D0 = 1:732 10 8 =s , yield stress 0 in a quasistatic simple tension test = 702MPa . Values of material parameters in the yield criterion and the evolution equation for the porosity are the same as those given in Batra and Jaber (2001). Note that in the Bodner-Partom relation, the plastic strain rate is positive even when the effective stress is less than the pertinent yield stress of the material. The plate is taken to be initially at rest, stress free, and at a uniform temperature. The normal velocity, v1 imposed on the impacted surface is given by v1=v0 = 8>>< >: 0:3t; 0 t 2 s; 0:525+0:0375t; 2 t 10 s; 0:9; 10 t ts; 0; t > ts; (2) where ts equals the time when the projectile separates from the plate. The expressions (2) for v1 are derived by fitting straight lines to the data of Batra and Ravisankar (2000). 3 COMPUTATION AND DISCUSSION OF RESULTS The aforestated problem is solved numerically by using an in-house developed finite element code. It employs constant strain triangular elements, lumped mass matrix obtained by the row sum technique, and the subroutine LSODE (Livermore Solver for Ordinary Differential Equations) for integrating the stiff set of coupled nonlinear ordinary differential equations. A reasonably fine mesh was employed in the region around the notch tip and the hole, and a coarse mesh elsewhere. Results presented herein have been computed with a fixed mesh.
RkJQdWJsaXNoZXIy MjM0NDE=