ICF10B

TABLE 3 NORMALIZED MAXIMUM SHEAR STRESSES tmax/ôs AND THEIR LOCATIONS y’max IN FEA TRANSVERSE IOSIPESCU MODEL Material Modeling Parameters EP/ET tmax/ôs y’max EP [MPa] ET [MPa] Virgin SIRCA 380 67 5.67 1.211 0.469 Charred SIRCA 630 170 3.71 1.160 0.450 Virgin SIRCA 130 34 3.82 1.163 0.449 Charred SIRCA 138 89 1.55 1.088 0.419 Virgin PICA 143 12 11.92 1.385 0.487 Charred PICA 107 33 3.24 1.139 0.449 The Iosipescu principal stress distributions were investigated under parallel and transverse loading, using both the compressive and the tensile values of EP and ET of SIRCA and using the compressive moduli of PICA in the FEA. Attention was focused on the region along surface BCDE, since that is where cracking was observed in the experiments. Figure 4 shows a representative example of the normalized, ordered, principal stresses óp1/ts and óp2/ts along BCDE, for transverse and parallel Iosipescu tests. The compressive values of EP and ET of virgin SIRCA were used in the calculations of Fig. 4. The position on the surface s’ is normalized by 2LCD (twice the length of CD), so that s’ = -0.5, 0, 0.5, and 0.9, respectively, correspond to positions at B, C, D, and E (s’ = 0 is at the notchroot). During transverse loading (Fig. 4a), the tensile stress óp1 is highly concentrated in the neighborhood of the notch-root, where it reaches a peak value of ómaxI at s’ = s’maxI, while the compressive stress óp2 is concentrated on the opposite side of the notch-root; óp1 also reaches a secondary maximum ómaxII at s’ = 0.900, which is at position E. The stress concentration at the notch-root explains why fracture occurs in a tensile mode near the notch tips during transverse loading (Fig. 2a). During parallel loading (Fig. 4b) óp1 is not peaked near the notch-root, but has a broad local maximum ómaxI at s’maxI in the region between C and D; in this mode, óp1 also reaches a peak value, ómaxII, at s’ = 0.888 which is close to E. These results are consistent with fracture patterns observed under parallel loading (Fig. 2b). Normalized tensile stress maxima, ómaxI/ts and ómaxII/ts, and the locations of ómaxI are listed in Table 4 for all of the materials and modeling conditions. During transverse loading, position smaxI is at a distance of roughly 5% of LCD from the notch-root, and in parallel loading it is at a distance of about 30% of LCD. It was also found that the maximum stresses in the region CD of the notch could be expressed as ómaxI/ts = 0.459ln(EP/ET) + 1.530, where 1.55 < EP/ET < 11.92, in the Iosipescu modeling under transverse loading, and ómaxI/ts = 0.0426ln(EP/ET) + 1.638, where 3.24 < EP/ET < 11.92, in the parallel loading models. Figure 4: Principal stress distribution on the surface BCDE of the Iosipescu specimen -0.5 0.0 0.5 Position s’ -5.0 -4.0 -3.0 -2.0 -1.0 0.0 1.0 2.0 3.0 sP/ts smaxI sp1 smaxII sp2 p -0.5 0.0 0.5 Position s’ -5.0 -4.0 -3.0 -2.0 -1.0 0.0 1.0 2.0 3.0 sP/ts smaxI sp1 smaxII sp2 (a) Transverse loading (b) Parallel loading

RkJQdWJsaXNoZXIy MjM0NDE=