ICF10B

0.20 0.40 0.60 0.80 1.00 1.20 1.40 1.60 0.0 5.0 10.0 15.0 20.0 M F /K IC h1.5b φ/(K IC /h0.5E) N P (2)=0.0 N P (2)=1.0 N P (2)=1.5 N P (2)=2.0 N P (1)=0.5 w C =300 (a) (b) 0.20 0.40 0.60 0.80 1.00 1.20 1.40 1.60 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 M F /K IC h1.5b ξ=a/h N P (2)=0.0 N P (2)=0.1 0.2 0.3 0.4 0.5 0.6 0.7 N P (1)=1.0 w C =300 1.2 1.3 1.5 1.4 1.6 1.7 1.8 0.8 0.9 1.0 1.1 1.9 E~ 0 20 40 60 80 100 120 140 160 0 10203040506070 P (KN) δ (mm) (c) N P (2)=3.09 w C =600 Experimental Theoretical N P (1)=1.28 Figure 3: (a) Dimensionless crack propagation moment vs normalized crack depth for fiber-reinforced concrete cross-section with N (1) P =1.0, ˜wE c =300 and N (2) P between 0.0 and 1.9. (b) Dimensionless crack propagation moment vs localized rotation diagram for a concrete cross-section as N (2) P varies, with N (1) P =0.5 and ˜wE c =300. (c) Comparison between the experimental load-deflection curve for a fiber-reinforced high-strength concrete [14] and the theoretical results (bridging option). the limit value, the process is stable, and a slow crack growth is possible also by increasing the applied load. The limit crack depth increases when the brittleness number N (2) P decreases. This result is consistent with the curves obtained by Carpinteri and Massabo` [13] for the cross-section with only secondary reinforcement. The dots in the figure indicate the primary reinforcement yielding points. It can be observed how the yielding point translates by varying the secondary brittless number N (2) P . From an engineering point of view, it appears very interesting to consider the crack propagation moment vs localized rotation diagram. Fig. 3.b shows the curves for N (1) P =0.5 and ˜wE c =300 and four different values of N (2) P . The first one (N (2) P =0.0) is representative of a fiber-reinforced concrete cross-section with no secondary reinforcement. The crack propagation moment shows a vertical asymptote for φ→0 (ξ →0). A vertical drop is achieved when the crack crosses the primary reinforcement. For N (2) P =0.0 and 1.5, a snap-through instability is present after the drop (dotted line), which is less and less evident for increasing values of N (2) P . The proposed theoretical model has been assessed by simulating an experimental test carried out by Ashour and Wafa [14] on high-strength concrete beams with the presence of two steel bar reinforcements. The beams, loaded in a four-point bending scheme, have a depth × thickness × span of 170 × 300 × 3680 mm. In the testing programme, 20 mm Grade 60 deformed steel bars having yield strength of 437 MPa were used as flexural reinforcement. The concrete mix proportion was 1:0.25:2.5 (cement:sand:coarse aggregate) to produce concrete

RkJQdWJsaXNoZXIy MjM0NDE=