even a small crack growth retardation. Similar experimental results were reported in [8]. This is not surprising because the monotonic plastic zone produced by the overloads increases with ∆K. An interesting feature that can be seen in figure 4 (b) is that after application of the first overload there was a delay retardation period that persisted for several thousands of cycles. During this period, the minimum crack growth rate was attained only after approximately 29000, 38000 and 55000 cycles for n=100, n=1000 and n=10000, respectively. Furthermore, crack growth rates lower than the following ones persisted for approximately 52000, 112000 and 125000 cycles for n=100, n=1000 and n=10000, respectively. CONCLUSIONS 1. The effect of block loading is similar to that observed for peak overloads. However, for this load sequence the retardation is always immediate. Load step-down leads to a greater increase in fatigue life than overloads. High-low sequences produce crack acceleration. 2. The phenomenon of plasticity-induced closure seems to be the dominant cause of the post-load variation crack growth transients in 6082-T6 aluminium alloy. 3. Increasing the difference between the initial stress intensity and the final stress intensity range, for high-low blocks, increases crack growth retardation. Furthermore, for equal step-down in loads retardation increases with the decrease of the lower ∆K. For low-high blocks acceleration increases with the final ∆K. 4. For less frequently applied overloads (n>10) crack retardation is observed, while the results for overloads applied after 10 baseline cycles present crack acceleration. ACKNOWLEDGEMENTS The authors would like to acknowledge POCTI programme, project 1999/EME/32984, for funding the work reported. REFERENCES 1. Shin, C.S. and Hsu, S.H. (1993) Int. J. Fatigue 15, 181. 2. Shercliff, H.R. and Fleck, N.A. (1990) Fatigue Fract. Engng. Mater. Struct 13, 297. 3. Fleck, N.A. (1988) Basic Questions in Fatigue: Volume 1, ASTM STP 924, 157. 4. Shuter, D.M. and Geary, W. (1995) Int. J. Fatigue 17, 111. 5. Ng’Ang’a, S.P. and James, M.N. (1996) Fatigue Fract. Engng. Mater. Struct 19, 207. 6. Ward-Close, C.M., Blom, A.F. and Richie, R.O. (1989) Engng. Fract. Mech. 32, 613. 7. Fleck, N.A. (1985) Acta Metall. 33, 1339. 8. Ohrloff, N., Gysler, A. and Lutjering, G. (1988). Mechanics of Fatigue Crack Closure, ASTM STP 982, 24. 9. Shijve, J. and Broek, D. (1962) Aircraft Engng. 34, 314. 10. Elber, W. (1971). Damage Tolerance in Aircraft Structures, ASTM STP 486, 230. 11. Christensen, R.H. (1959). Metal Fatigue. MacGraw-Hill, New York. 12. Jones, R.E. (1973) Engng. Fract. Mech. 5, 585. 13. Suresh, S. (1983) Engng. Fract. Mech. 18, 577. 14. Nicoletto, G. (1989). Nonlinear Fracture Mechanics:Volume I, ASTM STP 995, 415. 15. Borrego L.P., Ferreira J.M. and Costa J.M. (2001) Fatigue Fract. Engng Mater. Struct., in press. 16. Allison,J., Ku, C. and Pompetzki, A. (1988). Mechanics of Fatigue Crack Closure, ASTM STP982, 171. 17. Sehitoglu, H. and McDiarmid, D.L. (1980) Int. J. Fatigue 2, 55.
RkJQdWJsaXNoZXIy MjM0NDE=